Flowstop Ltd are now part of the ALH/ Pipe Equipment Specialists group. Online sales and enquiries will now go through Pipe Equipment Specialists.
Brass Hand Pump with 1 /4" BSP Connector.-
Flowstop Ltd are now part of the ALH/ Pipe Equipment Specialists group. Online sales and enquiries will now go through Pipe Equipment Specialists.
Flowstop air bags are designed to go through restricted openings measuring about 1/4 of the nominal pipe diameter or less. Manufactured from natural rubber bladder covered in proofer canvas.- Produced in cylindrical and spherical shapes.
- Standard range 1"-15" (25mm-375mm) Available with schrader valve as standard or brass cock as an extra.
- Larger range 16"-96" (400mm-2400mm) Come complete with ball valve.
-
Flowstop Ltd are now part of the ALH/ Pipe Equipment Specialists group. Online sales and enquiries will now go through Pipe Equipment Specialists.
The Eesiseel range of inflatable stoppers are designed for use where there is access to the full pipe bore: Eesiseel stoppers give the following benefits:- All pipe sizes from 1.9"-12.6" (48mm-320mm) can be sealed with just five Eesiseel Stoppers.
- Easy to achieve a good seal.
- Easy to inflate through a self-sealing car-type Schrader valve or brass cock.
- Very easy to clean.
- Robust and durable: will last a long time when properly cared-for.
- resistant to a large number of chemicals
- We have a 4″ (100mm) stopper with a 1/2″ (12.7mm) i/d tube through the centre of the bag, used for pressure testing. Other sizes can be manufactured upon request
-
Foam Pigs are used to remove dust or fluids from all pipe materials. They are generally pushed through a pipe using air or water pressure, although they can be supplied with a facility to allow them to be pulled through a pipe. Available in the size range 10mm to 1200mm. The prices online are for our basic soft foam pigs (1.5 lbs/cuft). For any bespoke pig or harder density versions, please contact our sales team.
-
For pressure testing and temporary sealing of gas, water, oil and sewerage pipes made of steel, cast iron, clay, plastic and concrete. For maximum allowable back pressures for each size of plug, please see attached the Datasheet in the document section. Please note that plugs must be suitably braced when applying any back pressure, in order to prevent the risk of accident.
-
Can be used to seal or test all types of pipe from 35mm up to 1200mm. 1.5 bar and 2.5 bar models available. The Pipe Equipment Specialists’ range of Inflatable Pipe Stoppers can be used to seal and test all type of pipes from 35mm up to 1200mm. Two models are available – Blank and Test. Two inflation pressures – 1.5 bar and 2.5 bar. Allowable Backpressure (Test Pressure) is equal to 50% of the Inflation Pressure.** Large expansion range. Lightweight – most sizes can be installed by one person. Can be supplied with any length of inflation hose. ** Maximum inflation & back pressure figures are for stoppers fully inserted into the pipe and mechanically braced against slippage. An Inflation assembly, complete with pressure relief and pressure gauge, suitable for use with an on site compressor, can be supplied separately. A Heavy Duty Hand Pump is also available.
-
Designed specifically for Directional Drilling to prevent the ingress of drilling fluid in the pipe. Available in the size range 32mm up to 500mm. Please contact us for any size not shown in the options below.
-
Flowstop Ltd are now part of the ALH/ Pipe Equipment Specialists group. Online sales and enquiries will now go through Pipe Equipment Specialists.
Nylon Air Bags are designed to go through restricted openings measuring about 1/4 of the nominal pipe diameter or less.- Manufcature from natural rubber bladder and covered in Grey proofed nylon.
- Produced in cylindrical and spherical shapes.
- Standard range 1"-15" (25mm-375mm). Available with Schrader valve as standard, or brass cock as an extra
- Standard range 16"-96" (400mm-2400mm).Supplied complete with ball valve.
- We can also supply a Nylon Bag c/w Centre Hole
-
Double Clevis Swivel for limited rotational applications. Used in winching applications to avoid damage to the cable or product pipe as a result of twisting winch wires. The Double Clevis Swivels feature a large clevis thereby avoiding the need for ‘D’ shackles and enabling direct connection onto Pipe Equipment Towing Heads. They are used in pipe bursting operations to ease rod and blade removals in two way bursts.
-
Our original and most popular Towing Head designed to work over a range of wall thicknesses for any particular pipe size. This can be supplied with or without a rear eye and with a flat plate in place of the nose cone. The Red Nose Towing Head has been designed to reduce the weight of the Standard Towing Head in sizes 200mm and above. The nose is made from PU.
-
Here at Pipe Equipment, we offer a comprehensive range of high quality valve keys to customers throughout the UK. Our valve operating keys are suitable for spindles of all shapes and sizes. The valve keys we offer are available on an individual basis or as universal key sets; which are perfect for people who work with several different types of spindle sizes or depths. No matter what type of pipe system you might be working with our valve keys are the perfect pipe equipment addition. Our range of valve operating keys can be used in a range of depths, meaning you can easily carry out work to your system or pipework. All of the pipe valve keys we offer are available to purchase online or if you have any questions about the products we offer, then please don’t hesitate to get in touch and one of our team will be more than happy to assist.
-
PECS (PE Coil to Straight) Connectors are a fully reusable product developed to overcome the problems encountered when passing coiled PE pipe through service cut outs whilst slip lining an existing metallic pipe using a pushing device attached to a mini digger. Please contact us for further details.
-
LINK SEALS are used to provide a seal between a product pipe or cable and a casing sleeve, duct or wall. LINK SEALS provide a modular hydrostatic sealing mechanism that is independent of internal or external pressure, and can provide a pressure seal up to 5 bar. LINK SEALS also provide electrical and vibrational insulation, and can provide fire resistance for up to three hours. The rubber material absorbs shocks and sounds, and reduces the vibration load on the pipes and cables. The unique link structure makes it possible to produce an almost unlimited number of sizes. Please download the data sheet to show different options available. Our sales team can advise suitable Link Seal and core hole sizes upon request. The seal is supplied in an assembled condition with the required number of links, and owing to its special design the LINK SEAL chain is rapidly installed.
-
Also known as Centralisers or Spiders, this product, which can be manufactured in plastic or metal, is used to centralise or position pipe within a sleeve or carrier pipe. Please contact our sales team who will be able to advise the most suitable size/model.
-
This kit of parts is designed to enable the new pipe or duct to be used as the air supply line to a pneumatic mole, thereby avoiding any potential problems resulting from collapsed bores. Available in sizes 20mm up to 63mm. Please contact our sales team for all available options.
-
Pipe Scrapers are designed to remove hard deposits and nodules. This type, which are also known as Christmas Tree Scrapers, are made up of a number of spring steel scrapers mounted on a high tensile steel central shaft. These scrapers remove deposits as they are winched through the pipe. The central shaft is fitted with a towing eye at each end to allow the scraper to be pulled back if necessary. They are available for all pipe sizes in the range 2″ (50mm) to 48″ (1200mm).
-
Wire Brush Pigs consist of two circular wire brushes mounted onto a high tensile steel central shaft with a towing eye located at each end. They are designed to be pulled through a metal pipe to remove loose deposits and dust prior to insertion of PE pipe. They can also be used after the Pipe Scraper to remove the deposits loosened by the scrapers. They are available from stock, for all common pipe sizes up to 12″ (300mm), with larger sizes available on request. Wire brushes are also available to mount on the front of a Towing Head to allow the metal pipe to be cleaned as the new PE pipe is installed.
-
Pull Throughs, also known as Squeegees and Plungers, are used to remove fine particles and fluids from pipes. They consist of two thick rubber discs mounted on a high tensile steel central shaft with a towing eye at each end. For applications where the pipeline contains tight bends a ‘flexible’ Pull Through can be supplied. This model has a chain linking the two discs, rather than a rigid central shaft. They are suitable for use with all pipe materials and are available in the size range 2″ (50mm) to 48″ (1200mm).
-
Duct Brushes are used to remove dirt and other loose debris from inside electrical or communication ducts. They are supplied either with an eye at both ends for pulling through ducts, or with a M12 fitting for pushing through ducts using a Cobra (Flexible Fibreglass Rod). They are available to suit ducts from 2″ (50mm ) to 16″ (400mm).
-
The Pipe Equipment Gas-Vac™ Systems utilise a lightweight hand held venturi 'gun', powered by an on-site compressor or nitrogen bottle, to perform several different functions within the gas distribution industry. Originally devised by Operational Transco Engineers, Gas-Vac™ is predominantly utilised for service dewatering and has undergone a series of tests and field trials to ensure it meets the required safety and performance standards.
-
This product is designed to pull a number of smaller pipes or cables into a directionally drilled bore or into an existing pipe or duct. Please contact us for prices and information.
-
Similar to the Standard model except that this model has an additional sealing ring which will withstand an internal pressure of 10 bar. This design also prevents the ingress of dirt and fluid and the contamination of a pre-chlorinated pipe. Available in the size range 25mm to 500mm. Please contact us for prices and information.
-
This towing head is fused onto the PE pipe string and features a strong sealed, but rotating, eye bolt, thus ensuring a fully sealed towing head. Suitable for directional drilling, slip lining and direct burial. Available in the size range 90mm to 500mm plus. Please contact us for prices and information.
-
Designed to be bolted to the outside, or inside, of large diameter PE pipes. This is a cost effective alternative to other models where speed of installation / removal is less critical. Available in the size range 400mm to 1200mm. The Bolt-On Towing Head has been designed as a cost effective solution to the problem of obtaining a strong and reliable pulling attachment onto larger (400mm +) PE pipes of any wall thickness (SDR). It is available as a sealed, or unsealed unit making it suitable for both Directional Drilling and Slip Lining applications as well as a method of pulling PE pipes during direct burial installations. On the sealed variant the Towing Head is supplied already attached to a metre length of capped PE pipe. The unsealed variant is usually supplied as a bare unit suitable for fitting on site to a pipe section. For applications where it is not desirable to increase the outside diameter of the pipe by even a small amount, i.e. tight fit slip lining, the Bolt-On Towing Head can be manufactured to fit inside the PE pipe and therefore not increase the outside diameter at all. Please contact us for prices and information.
-
Developed for the PE manufacturer, this model has been designed to quickly and simply attach the newly produced pipe to the coiling machine without damaging the internal or external surfaces. Available in the size range 90mm to 1000mm plus. Please contact us for prices and information.
-
- Winch placed into manhole 1. (See attached data sheet)
- Winch rods inserted into old pipe from manhole 1 and connect to head in manhole 2
- Head winched into old pipe, which is broken and displaced
- New Pipe is located in shield on rear of head and held in place by simple tensioning device.
- Head is again winched forward. New pipes are snapped together behind the head as it is winched forward.
- Above step is repeated until full length is in place.
-
The Pipe Equipment Pipe Support Rollers have been specially designed to ease the problems of handling plastic pipes during jointing and installation. They greatly reduce the chances of pipe damage as a result of the pipe string being trailed along the ground and keep pipe drag to a minimum. Pipe Support Rollers are available as ‘Free Standing’ or ‘In Trench’.
-
Used to provide a temporary water and dirt seal at the end of a pipe. Useful for sealing road crossings laid prior to the main pipeline. Please contact us for prices and information.